Product Information:

The premium quality custom-fit car covers from Coverking, the Coverbond-4 car covers are especially made to protect your vehicle against UV rays. As the name suggests, the outdoor car covers are made of four layers. The topmost layer is made of Polyester Spun Bond. The high strength fabric guarantees the superb effectiveness. The material is strong and provides long lasting protection against varieties of hazards.

While the upper middle layer made of 4% UV treated Polypropylene Spunbond ensures optimum UV protection, the lower middle Melt Blown material layer makes car covers water resistant. Finally the bottom layer made of Polypropylene Spunbond material again makes Coverbond-4 car covers strong and durable.

Coverbond-4 car covers are best for moderate weather conditions and can be used for both indoor as well as outdoor purposes.  Coverking’s Coverbond-4 car covers are bulky. Such a thick construction provides effective protection against scratches, minor dents etc. Our custom car covers breathe well.  Coupled with water resistant properties, the breathability allows trapped moisture to escape and prevent rust damage.

Feature Guide:

• Four  layered construction for optimum protection
  • Top layer: Polyester Spun Bond makes car covers strong and durable
  • Upper Middle layer: UV treated Polypropylene Spunbond for greater UV protection
  • Lower middle layer: Melt Blown material makes car covers water resistant
  • Bottom layer: Polypropylene Spunbond material further strengthen the car covers
• Bulky construction for effective protection against scratches, minor dents etc
• UV treated car covers provide exceptional UV protection
• Tough, strong and long lasting
• Enhanced breathability
• Greater dirt/dust protection
• High tensile strength
• Provides soft touch to your car
• Superb water resistance
• Better heat insulation material
• Least color fading
• Shrink resistant
• Abrasion resistant
• Easy to handle: Install, remove, clean and store
• Suitable for moderate weather conditions
• Useful for both indoor and outdoor purposes

Installation Guide:

Installation of your Coverbond-4 Car Cover is quite easy and it can be done just by draping the car cover around your vehicle body. But before moving ahead to install the car cover around your vehicle, you are required to adopt a couple of precautionary steps.  These steps are a part of your preparation for installing the Coverbond-4 Car Cover and they are mentioned below:

First of all, before moving ahead to install the Coverbond-4 Car Cover, ensure that your vehicle body is made dust free and cleaned properly. Without cleaning your vehicle appropriately, if you drape the Coverbond-4 Car Cover around it, dust particles would stick to your car cover and unleash damage to the fabric finish.

Never install your Coverbond-4 Car Cover over a wet vehicle.

Coverbond-4 Car Cover Installation:

The Coverbond-4 Car Cover installation process includes a couple of steps and they are mentioned below:

Coverking`s car covers are available in rolled packages and as such they are to be unrolled first for proper installation. In the very first installation step, you are required to place the Coverbond-4 Car Cover over the hood of your vehicle and unfold it.

Now, if the car cover is equipped with mirror pockets, install them first before moving ahead to cover the front and rear bumpers of your vehicle. Installation of the   mirror pockets in the first place would keep the Coverbond-4 Car Cover fixed firmly over your car in stormy weather conditions.  

Now, after installing the mirror pockets, drape the Coverbond-4 Car Cover over the front and rear bumpers of your vehicle.

Coverbond-4 Car Cover Lock Kit Installation:

If you have bought an extra lock kit with your Coverbond-4 Car Cover, you can install it properly and protect your car cover from bring stolen away by thieves. The car cover lock kits have a vinyl coated cable with a metal piece attached to one end and a loop at the other end. Now, to install the lock kit, proceed to the passenger’s corner of the covered vehicle and fix the cable loop at around two inches through the grommet. After that, push the metal piece end to the driver’s side by pulling it along under the grommet through the loop of the first cable. Now after reaching the driver’s corner, push the cable from outside the cover by two inches via the grommet and then lock the end piece of the cable.

Specific Measures To Be Adopted During Coverbond-4 Car Cover Installation:

While installing the Coverbond-4 Car Cover, you should adopt a few extra precautionary measures to ensure hassle-free and successful installation. These are, namely:

Never keep the car cover in contact with the exhaust tips if they are too hot or are sharply edged. This is because as soon as the Coverbond-4 Car Cover touches the exhaust tips, it may undergo melting instantly.

If your car is fitted with an antenna, you should undertake a separate installation procedure. To install Coverbond-4 Car Cover over such a vehicle, you should induce an opening in your car cover. To achieve this, remove the car cover first and position the antenna. Now, figure out the particular point where the antenna meets the base and cut out a small portion of your car cover at this point. Now, install the antenna and then place the Coverbond-4 Car Cover over the antenna properly, duly covering the antenna patches.

Cleaning Instruction: 

The Coverbond-4 Car Cover cleaning process includes two principal procedures: hand washing and machine cleaning. Altogether, the Coverbond-4 Car Cover can be cleaned by bringing the inner out and spreading water on it by using a hose. Simple hand washing is applicable for Coverbond-4 Car Covers that are not considerably dirty and you can also use large-sized automatic speed control washers (M/Cs) for proper cleaning of your Coverbond-4 Car Covers. However, agitators are not recommended to be used in machine cleaning as the use of agitators can rip off the fabric of your Coverbond-4 Car Cover.

Coverbond-4 Car Cover Cleaning Process:

First of all, get hold of a non-caustic, bio-degradable, non-toxic and eco-friendly anionic detergent. Take two cups of this detergent, mix with warm/ cold water and then leave the Coverbond-4 Car Cover on it to soak for 5 minutes. Thereafter, wash the Coverbond-4 Car Cover with gentle cycles for a 5-minute period. Thereafter, rinse the Coverbond-4 Car Cover with two cycles and again rinse it with one cycle to make it half dry. Now, pick up the half-dried Coverbond-4 Car Cover and leave it over the vehicle to be dried completely by air effect.